Study on the influence of segmented fuel cell by grooving method and its application in oxygen starvation diagnosis

The oxygen starvation in fuel cells is an important reason for the deterioration of durability. The segmented fuel cell is a method to study the gas distribution inside the fuel cell. In order to study the influence of the grooving method on segmented fuel cell and its application in oxygen starvation diagnosis, a five-serpentine-channel three-dimensional two-phase simulation model is established by FLUENT. Through steady-state simulation, the effect of grooving method on fuel cell performance is studied. The overall performance (polarization curve) of the fuel cell drops slightly, but the current density distribution on the anode graphite plate changes greatly due to the grooves. The “current concentration” phenomenon is proposed based on the current density distribution. Through dynamic simulation, the oxygen starvation under current load mode and voltage load mode is simulated, and the “starvation coefficient” is defined as an oxygen starvation diagnostic index. In the current load mode, the “starvation coefficient” never exceed 15%, because when the oxygen starvation is severe, the simulation cannot converge or even cannot maintain, which corresponds to the voltage reversal in reality. However, in the voltage load mode, the “starvation coefficient” can reach up to 100%. The conclusions have important guiding significance for the judgment of the internal reaction uniformity of the segmented fuel cell by grooving method and provide a theoretical basis for judging whether a fuel cell is out of oxygen by segmented fuel cell.     

The effect of biomass feeding location on rice husk gasification for hydrogen production

The objective of this study is to investigate the impact of biomass feeding location on rice husk gasification for hydrogen production. By comparing the results between top-feed and bottom-feed of the feedstock of the fluidized bed biomass gasification at the reaction temperature between 600～1000 °C and ER = 0.2, 0.27, and 0.33 without steam, the optimum low heating value was increase by 2.35 kJ/g-rice husk by the top-feed to gasifier. Although the yield of hydrogen was decreased by 42% for the rice husk gasification by the top-feed operation, the yield of CO, CO2, and CH4 were highly increased, which enhancing the heating value of the effluent gas. The study results suggested the potential route of the biomass gasification at the different feeding location.     

南水北调中线总干渠藻类的生态调度

南水北调中线总干渠无在线调蓄水库,对藻类生态调度过程中出现的问题开展生态调度实现策略和实施方式研究。主要实现策略包括:划定自身的调蓄区,隔离生态调度对下游的影响;采用高效的渠池运行方式,减少生态调度时蓄量的反复调整;综合考虑安全、快速、平稳等需求,设定生态调度实施进程和方式。具体实施方式包括:将总干渠划分为流速调控区、调蓄区和正常运行区,分别实施等体积、控制蓄量和闸前常水位方式运行;将生态调度过程划分为充水阶段和泄水阶段,基于流速调控目标值、持续时长和水位降幅约束条件,确定各阶段时长和各分区的闸门群调控方案等。基于2018年3月输水工况,采用明渠一维非恒定流模型,仿真总干渠上游15个渠池的藻类生态调度过程。结果表明,生态调度可在3.5 d内完成,各渠池的平均流速由0.48 m/s增至0.93 m/s,持续时间超过2 h。在整个生态调度过程中,水位变化平稳,水位变幅符合安全阈值要求,下游渠道的正常运行未受生态调度明显影响。     

基于VMD和BSA-KELM的高陡边坡位移预测模型研究

边坡位移的时间序列曲线存在复杂的非线性特性,传统的预测模型精度不足以满足预测要求。为此提出了基于变分模态分解的鸟群优化-核极限学习机的预测模型,并用于河北省某水泥厂的边坡位移预测。该方法首先采用VMD把边坡位移序列分解为一系列的有限带宽的子序列,再对各子序列分别采用相空间重构并用核极限学习机预测,采用鸟群算法优化相空间重构的嵌入维度和KELM中惩罚系数和核参数三个数值,以取得最优预测模型。最后将各个子序列预测值叠加,得到边坡位移的最终预测值。结果表明：和KELM、BSA-KELM、EEMD-BSA-KELM模型相比,基于VMD的BSA-KELM预测精度更高,为边坡位移的预测提供一种有效的方法。     

Thermal properties of hierarchical YSZ and LZO ceramic microspheres with multi-scaled voids investigated by using theoretical,experimental and simulation methods

Heat transfer within ceramic feedstock powders is still unclear, which impedes optimization of the thermal and mechanical properties of the thermal sprayed coatings. The microspheres (yttria-stabilized zirconia YSZ and lanthanum zirconate LZO) were prepared via the electro-spraying assisted phase inversion method (ESP). The thermal properties of the two ESP microspheres and a commercial hollow spherical powder (HOSP) were investigated by using theoretical, experimental, and simulation methods. Thermal conductivity of the single microsphere was estimated via a novel nest model that was derived from the Maxwell-Eucken 1 and the EMT model. Thermal conductivity of a single YSZ/LZO-ESP microsphere prepared at 1100–1200 °C was within 0.36–0.75 W/m K, which was ～ 20 % lower than that of a single YSZ-HOSP microsphere with a similar porosity. Heat flux simulation showed that high tortuosity around the multi-scaled voids of the ESP microsphere led to a more efficient decrease in thermal conductivity compared with total porosity.     

两种混合单元混合机理的数值模拟

为了研究SV型和SX型混合单元在全静态乳化器的混合机理,使用群体平衡模型对乳化器内部流场进行模拟分析。结果表明,SV型与SX型混合单元的混合机理是油相与水相材料通过混合单元时其空间流动方向改变,在流场内形成大量的漩涡,从而达到乳化的目的;通过比较流体在经过SV型和SX型混合单元后的水相索特平均直径(d_(32)),得出SV型混合单元的乳化效果更强,但同时消耗更多的能量,压降更大。     

Directional separation of hydrogen-containing gas mixture by hydrate-membrane coupling method

Recovery of hydrogen (H₂) from H₂-containing gas mixtures has great significance for energy conservation, cost reduction and benefit increase. However, the common separation methods have the ubiquitous problem due to phase equilibrium principle and results in the conflict between H₂ concentration and H₂ recovery rate in the product gas. Consequently, an innovative conception of hydrate-membrane coupling approach is proposed in this work. In the separation process, hydration and membrane permeation two separation driving forces coexist to achieve the aim of strengthening mass transfer kinetics. H₂ and non-H₂ components (hydrocarbons) are synchronously and directionally selected by membrane and hydrate to improve different phase compositions. Therefore, the gas in feed side could keep relatively high two separation driving forces (H₂ fugacity and hydrocarbons fugacity). The results show that the coupling method could synchronously increase both the concentration and the recovery rate of H₂ in the product gas. At the same time, the volume and concentration of the hydrocarbons in hydrate both increases effectively. It indicates that hydrate and membrane separation methods support each other in the separation process. The hydrate-membrane coupling method fundamentally solves the issue of the decreasing driving force resulting from single separation method and phase equilibrium relationship.     

Numerical simulation of the influence of confined multi-point ignited H2–O2 mixture on the propagation of shock waves towards a deformable plate

The study of shock wave propagation in a detonation chamber is of great importance as a part of the plate forming process. Investigations related to the effects of premixed gas detonation on the deflection of a plate require in-depth examination. An Eulerian-Lagrangian numerical simulation is conducted using the space-time conservation element and solution element method of LS-DYNA software to study the effect of confined multi-point ignited gaseous mixture on the dynamic response of thin plates clamped at the end of a combustion chamber. The FSI couples a Lagrangian finite element solver with a Eulerian fluid solver in a 2D space with detailed chemistry of H₂–O₂ mixture. The solution contains the detonation wave propagation through the combustion chamber and its interaction with the plate. The influence of variation in the multi-point ignition locations and combustion chamber dimensions on the pressure history and plate deflection is studied. To verify the model, a comparison with the experimental study is carried out using an adjustable model representative of the real experiment. The verified model is used to link the evolution of plate shape with the arrival time and intensity of shock waves within the chamber. It is found that a longer distance between the ignition point and the plate intensifies the ultimate deflection of the plate. In addition, a fairly large combustion area employed in a direction rather than transverse to the plate surface is unable to influence the ultimate deformation of the plate.     

Development of a stakeholder identification and analysis method for human factors integration in work system design interventions – Change Agent Infrastructure

In any work system design intervention—for example, a physical workplace re-design, a work process change, or an equipment upgrade—it is often emphasized how important it is to involve stakeholders in the process of analysis and design, to gain their perspectives as input to the development, and ensure their future acceptance of the solution. While the users of an artifact or workplace are most often regarded as being the most important stakeholders in a design intervention, in a work-system context there may be additional influential stakeholders who influence and negotiate the design intervention's outcomes, resource allocation, requirements, and implementation. Literature shows that it is uncommon for empirical ergonomics and human factors (EHF) research to apply and report the use of any structured stakeholder identification method at all, leading to ad-hoc selections of whom to consider important. Conversely, other research fields offer a plethora of stakeholder identification and analysis methods, few of which seem to have been adopted in the EHF context. This article presents the development of a structured method for identification, classification, and qualitative analysis of stakeholders in EHF-related work system design intervention. It describes the method's EHF-related theoretical underpinnings, lessons learned from four use cases, and the incremental development of the method that has resulted in the current method procedure and visualization aids. The method, called Change Agent Infrastructure (abbreviated CHAI), has a mainly macroergonomic purpose, set on increasing the understanding of sociotechnical interactions that create the conditions for work system design intervention, and facilitating participative efforts.